General OperationLCD Programming FunctionsResetting Default Settings

General Operation

FunctionOperation
Power Save ModeAfter the machine is idle for 1 hour, it will enter into a POWER SAVE mode, being brought back to functionality with the touch of any of the button (other than the POWER) or operating the either the STEAM LEVER or HOT WATER dial. Pressing the POWER button while in POWER SAVE mode will shut the machine off.
LCD InterfaceDisplay Modes:
1. Shot Temp
-Default is 200°F(93°C)
-Can be adjusted from 190°F to 205°F (86°C - 96°C)
2. Shot Clock
-Displays the duration off the current extraction in seconds
3. Clock
-Displays the current time. Default is set to 12:00AM if the time has not been sent.
1 CUP BUTTONPressing the 1 CUP button will extract a single shot of espresso, pre-programmed to approximately 1oz.
2 CUP BUTTONPressing the 2 CUP button will extract a double shot of espresso pre-programmed to approximately 2 oz.
MANUAL BUTTONThe MANUAL button allows you to control the espresso pour volume to suit your preference. Pressing the MANUAL button once will start the extraction with a low pressure pre-infusion. The extraction will continue until the MANUAL button is pressed again to stop the flow.
STEAMFor instant steam, move the STEAM LEVER to the OPEN position. The STEAM LED will illuminate and will remain so until the lever is moved to the CLOSED position.
HOT WATERFor instand hot water, rotate the HOT WATER dial to the OPEN position. The HOT WATER LED will illuminate and will remain so until the dial is moved to the CLOSED position

LCD Programming Functions

THE LCD can be used to do simple programming for the Dual Boiler™.

FunctionProgram
1 CUP Volume ProgrammingPress the MENU button until SHOT VOL is flashing on the top of the screen and 1CUP is showing on the lower part. Press the 1 CUP button to start the extraction. Press the 1 CUP button again to stop the extraction when the appropriate amount has poured. The machine will beep twice. Press the EXIT button to set the new volume.
2 CUP Volume ProgrammingPress the MENU button until SHOT VOL is flashing on the top of the screen and 2CUP is showing on the lower part. Press the 2 CUP button to start the extraction. Press the 2 CUP button again to stop the extraction when the appropriate amount has poured. The machine will beep twice. Press the EXIT button to set the new volume.
Extraction TemperaturePress the MENU button until SHOT TEMP is flashing on the top of the LCD screen. The lower portion of the screen will show the current temperature setting. Press the UP or DOWN arrow to adjust the SHOT TEMP to the desired setting. Once the desired temperature is adjusted to, press the EXIT button to set the new extraction temperature.
SET CLOCKPress the MENU button until SET CLOCK is flashing on the top of the LCD screen. The default is 12:00AM if the time has not yet been set. Press the UP or DOWN arrow to adjust the time. For faster scrolling, press and hold the UP or DOWN arrow. Once the desired time is reached, press the EXIT button to set the clock.
AUTO STARTIn order to set the AUTO START feature, the time must be set first. It is recommended that the AUTO START be set to 30 minutes before the intended time of use to allow for proper heating of the machine.
Turning the AUTO START ON/OFFPress the MENU button until AUTO START is flashing on the top of the LCD screen. The current selection (ON or OFF) will show on the lower section of the LCD screen. Press the UP or DOWN arrow to set the AUTO START to ON or OFF. If AUTO START is turned ON, a clock icon will show in the bottom left hand corner of the LCD screen.
AUTO START - Setting the ON time.Ensure that the AUTO START is set to on. Press the MENU button until the AUTO START icon flashing and the current start time is displayed on the LCD screen. The time is 7:00AM by default. Press the UP or DOWN arrow to adjust to the desired time. Press the EXIT button to set the new AUTO START time.

Resetting Default Settings

The machine can be reset to it’s default factory settings if desired very quickly.

  • Switch the machine OFF
  • Press and hold both the 1 CUP and 2 CUP buttons. While holding them down, press the POWER button.
  • The LCD will display REST.
  • all programmed settigns will then be reset back to the default settings
  1. Temperature – 200°V (93°C)
  2. Pre-Brew Infusion – PP60, Pd07 seconds (PP pressure – Pd duration).
  3. Auto Start – OFF
  4. Auto Start Time – 7:00AM
  5. Audio – LO
  6. Clock – 12:00AM
  7. Temperature Unit – Fahrenheit
  8. Auto Power Off – ON
  9. 1 CUP default volume – approximately 1oz/30mL
  10. 2 CUP default volume – approximately 2oz/60mL.