Care

After Every Use

Here’s the everyday checklist; an explanation of each step follows after.

Do not use abrasive cleansers, pads or cloths which can scratch the surface. Do not clean any of the parts or accessories in the dishwasher.

Cleaning the Filter Baskets & Portafilter

  • The filter baskets and portafilter should be rinsed under hot water immediately after use to remove all residual coffee oils.

  • If any of the holes in the filter basket become blocked, use the pin on the end of the provided cleaning tool to unblock the hole(s).

  • If the hole(s) remain blocked, dissolve a cleaning tablet in hot water and soak filter basket and portafilter in solution for approx. 20 minutes. Rinse thoroughly.

Cleaning the Shower Screen

  • The group head interior and shower screen should be wiped with a damp cloth to remove any ground coffee particles.

  • Periodically purge the machine. Place an empty filter basket and portfilter into the group head. Press and hold the 1 CUP button and run a short flow of water to rinse out any residual coffee.

Cleaning the Drip & Storage Tray

  • The drip tray should be removed, emptied and cleaned after each use or when the drip tray indicator is showing 'EMPTY ME!'.

  • Remove the grill from the drip tray. Wash both in warm soapy water. The 'EMPTY ME!' indicator can also be removed and cleaned separately.

  • The storage tray can be removed and cleaned with a soft, damp cloth. Do not use abrasive cleansers, pads or cloths to clean any part of the machine as they can scratch the surfaces.

Cleaning the Steam Wand

  • Immediately after texturing milk, turn steam on to purge out any residual milk from the steam wand then wipe the wand with a damp cloth.

  • If any of the holes in the tip of the steam wand become blocked, ensure the STEAM/HOT WATER dial is in the STANDBY position. Press the POWER button to turn the machine Off and allow to cool. Use the pin on the end of the provided cleaning tool to unblock the hole(s).

  • If the steam wand remains blocked, remove the tip using the integrated spanner in the cleaning tool and soak in hot water. Use the pin on the end of the provided cleaning tool to unblock the hole(s) before re-attaching to the steam wand.

Cleaning the Outer Housing & Cup Warming Tray

  • The outer housing and cup warming tray can be cleaned with a soft, damp cloth. Polish with a soft, dry cloth. Do not use abrasive cleansers, pads or cloths which can scratch the surface.

 

Periodic Maintenance

Here’s a checklist of basic long-term maintenance; each step is explained after.

WARNINGDo not immerse power cord, power plug or appliance in water
or any other liquid.

Decalcifying

After regular use, hard water can cause mineral build up in and on many of the inner functioning components, reducing the brewing flow, brewing temperature, power of the machine, and taste of the espresso. We advise decalcifying the machine every month and especially if not using the machine for an extended period, e.g., before going on vacation. Replacing the water filter every two months will reduce the need to decalcify the machine.

WARNINGThe water tank should never be removed or completely emptied
during decalcifying.
TO DECALCIFY:
  1. Remove the portafilter.

  2. Pour a 50:50 mixture of white vinegar and cold tap water into the water tank.

  3. Place a large container beneath the group head and steam wand.

  4. When the brewing temperature has been reached and all the button surrounds on the control panel have illuminated, press and hold the 1 CUP button to commence a manual pour. Release the button once half the mixture of white vinegar and water has run through the group head.

  5. Set the STEAM/HOT WATER dial to the hot water position and allow hot water to run through the hot water outlet for approximately 30 seconds. Return the dial back to the STANDBY position.

  6. Set the STEAM/HOT WATER dial to the steam position and allow steam to run through the steam wand for approximately 2 minutes. Return the dial back to the STANDBY position.

  7. If any of the mixture remains in the water tank, press and hold the 1 CUP button to commence a manual pour. Release the button once the tank is empty and nothing runs through the group head.

  8. In harder water environments, we recommend repeating this cycle.

  9. After decalcifying, remove the water tank and rinse thoroughly then refill with fresh cold water only. To rinse the machine, repeat the steps above.

Replacing the Water Filter

The provided water filter helps prevent scale build-up in and on many of the inner functioning components. Replacing the water filter every two months will reduce the need to decalcify the machine.
If you live in a hard water area, we recommend you change the water filter more frequently. The water filter should be removed if using filtered or bottled water.
Remove and discard the old water filter from the filter holder; remove the new water filter from the plastic bag.

1.Soak the water filter in a cup of water for 5 minutes, then rinse under cold running water.
2.Wash the water filter holder with cold water, taking specific care to rinse the stainless steel mesh.
3.Insert the water filter into the two parts of the water filter holder.
4.Set Date Dial 2 months ahead.
5.To install the assembled water filter holder into the water tank, align the base of the water filter holder with the adapter inside the water tank. Push down to lock into place.
6.Slide the water tank back into position at the back of the machine, ensuring to push down completely to lock into place.

Cleaning Cycle

The CLEAN ME light will illuminate when a cleaning cycle is required. This is a back-flushing cycle and is separate from decalcifying. (Additional espresso cleaning tablets are available at BrevilleUSA.com.)

TO RUN THE CLEANING CYCLE:
  1. Insert the 1 CUP filter basket into the portafilter, followed by the supplied cleaning disc, followed by 1 cleaning tablet.

  2. Lock the portafilter into the group head.

  3. Place a large container beneath the group head.

  4. Ensure the water tank is filled with cold water and the drip tray is empty.

  5. Press the POWER button to turn the machine Off.

  6. While pressing the 1 CUP and 2 CUP buttons, simultaneously press the POWER button. Hold all 3 buttons together for 10 seconds.

  7. The cleaning cycle will commence and last for approximately 5 minutes. During this time, water will intermittently pour from the group head. Once complete, 3 beeps will sound.

  8. Remove the portafilter and ensure the tablet has completely dissolved. If the tablet has not dissolved, repeat until the tablet has dissolved.

Silicone Seal & Using the Allen Key

Over time, the silicone seal surrounding the shower screen will need to be replaced to ensure optimum brewing performance.

1.Press the POWER button to turn the machine Off and unplug the cord from the power outlet.
2.Carefully remove the rear water tank and drip tray, taking particular care if they are full.
3.Using a skewer or similar, clean the center of the screw of any residual coffee.
4.Insert the shorter end of the Allen Key into the center of the screw. Turn counter-clockwise to loosen the screw.
5.Once loosened, carefully remove and retain the screw and stainless steel shower screen. Make note of the side of the shower screen that is facing downwards. This will make re-assembly easier. Wash the shower screen in warm soapy water, then dry thoroughly.
6.Remove the silicone seal with your fingers or a pair of long-nose pliers. Insert the new seal, flat side first, so the ribbed side is facing you.
7.Re-insert the shower screen, then the screw. With your fingers, turn the screw clockwise for 2-3 revolutions then insert the Allen Key to tighten until the screw is flush with the shower screen.
8.Re-insert the drip tray and rear water tank.

WARNINGDo not immerse power cord, power plug or appliance in water
or any other liquid.